View NCP606_2844368.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? semiconductor components industries, llc, 2007 november, 2007 - rev. 0 1 publication order number: ncp605/d ncp605, NCP606 500ma, low i gnd , cmos ldo regulator with/without enable and with enhanced esd protection the ncp605/NCP606 provide in excess of 500 ma of output current at fixed voltage options or an adjustable output voltage from 5.0 v down to 1.25 v. these devices are designed for space constrained and portable battery powered applications and offer additional features such as high psrr, low noise operation, short circuit and thermal protection. the devices are designed to be used with low cost ceramic capacitors and are packaged in the dfn6 3x3.3. ncp605 is designed without enable pin, NCP606 is designed with enable pin. features ? output voltage options: adjustable, 1.5 v, 1.8 v, 2.5 v, 2.8 v, 3.0 v, 3.3 v, 5.0 v ? adjustable output by external resistors from 5.0 v down to 1.25 v ? current limit 675 ma ? low i gnd (independent of load) ? 1.5% output voltage tolerance over all operating conditions (adjustable) ? 2% output voltage tolerance over all operating conditions (fixed) ? ncp605 fixed is direct replacement lp8345 ? typical noise voltage of 50 v rms without a bypass capacitor ? enhanced esd ratings: 4 kv human body mode (hbm) 400 v machine model (mm) ? these are pb-free devices typical applications ? hard disk drivers ? notebook computers ? battery power electronics ? portable instrumentation figure 1. ncp605 typical application circuit for fixed version (1.5 v, 1.8 v, 2.5 v, 2.8 v, 3.0 v, 3.3 v, 5.0 v) ncp605 (fixed) v in v out sense gnd v out v in c in c out dfn6, 3x3.3 mn suffix case 506ax see detailed ordering and shipping information in the package dimensions section on page 12 of this data sheet. ordering information marking diagram http://onsemi.com 1 xxxx zzz ayww xxxx = p605 or p606 zzz = adj, 150, 180, 250, 280, 300, 330, 500 a = assembly location y = year ww = work week = pb-free package (note: microdot may be in either location) 1 2 3 6 5 4 gnd nc sense/adj 1 2 3 6 5 4 gnd en sense/adj gnd gnd ncp605 pin connections dfn6 3x3.3mm NCP606 pin connections dfn6 3x3.3mm (top view) (top view) v in v in v out v in v in v out
ncp605, NCP606 http://onsemi.com 2 figure 2. NCP606 typical application circuit for fixed version (1.5 v, 1.8 v, 2.5 v, 2.8 v, 3.0 v, 3.3 v, 5.0 v) NCP606 (fixed) v in v out sense gnd v out v in c in c out en figure 3. ncp605 typical application circuit for adjustable version (1.25 v < v out 5.0 v) ncp605 (adjustable) v in v out adj gnd v out v in c in c out NCP606 (adjustable) v in v out adj gnd v out v in c in c out figure 4. NCP606 typical application circuit for adjustable version (1.25 v < v out 5.0 v) en figure 5. ncp605 typical application circuit for adjustable version (v out = 1.25 v) ncp605 (adjustable) v in v out adj gnd v out c in c out figure 6. NCP606 typical application circuit for adjustable version (v out = 1.25 v) NCP606 (adjustable) v in v out adj gnd v out c in c out en v in v in r 1 r 2 r 1 r 2 figure 7. ncp605 simplified block diagram figure 8. NCP606 simplified block diagram - + driver with current limit thermal shutdown v ref gnd sense/adj fixed version only adjustable version only - + driver with current limit thermal shutdown v ref gnd sense/adj fixed version only adjustable version only en v in v out v in v out
ncp605, NCP606 http://onsemi.com 3 pin function description pin no. pin name description 1 v in positive power supply input* 2 gnd power supply ground 3 nc/en ncp605: this pin is not connected NCP606: this pin is enable input, active high 4 v out regulated output voltage 5 sense/adj output voltage sense input fixed version: connect directly to output capacitor adjustable version: connect to middle point of external resistor divider 6 v in positive power supply input* epad gnd exposed pad is connected to ground *pins 1 and 6 must be connected together externally for output current full range operation absolute maximum ratings rating symbol value unit input voltage range (note 1) v in -0.3 to 6.5 v chip enable voltage range (NCP606 only) v en -0.3 to 6.5 v output voltage range v out -0.3 to 6.5 v output voltage/sense input range, sense/adj v adj -0.3 to 6.5 v esd capability human body model machine model esd 4000 400 v maximum junction temperature t j(max) 150 c storage temperature range t stg -65 to 150 c stresses exceeding maximum ratings may damage the device. maximum ratings are stress ratings only. functional operation above t he recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may af fect device reliability. note: this device series contains esd protection and exceeds the following tests: esd human body model tested per aec-q100-002 (eia/jesd22-a114) esd machine model tested per aec- 150 ma per jedec standard: jesd78q100-003 (eia/jesd22-a115) latchup current maximum rating: 150 ma per jedec standard: jesd78. 1. minimum v in = (v out + v do ) or 1.5 v, whichever is higher. thermal characteristics rating symbol value unit thermal resistance, junction-to-ambient (note 2) r ja 75 c /w thermal resistance, junction-to-case r jc 18 c /w 2. soldered on 645 mm 2 , 1 oz copper area, fr4. refer to electrical characteristics and application information for safe operating area. operating ranges (note 3) rating symbol value unit input voltage (note 4) v in 1.5 to 6.0 v output current (notes 5 and 6) i out 0 to 675 ma junction temperature t j -40 to 150 c ambient temperature t a -40 to 125 c 3. refer to electrical characteristics and application information for safe operating area. 4. minimum v in = (v out + v do ) or 1.5 v, whichever is higher. 5. minimum limit valid for fixed versions only. for more details refer to application information section. 6. maximum limit for v out = v out(nom) - 10%.
ncp605, NCP606 http://onsemi.com 4 electrical characteristics v in = (v out + 0.5 v) or 1.5 v, whichever is higher, c in = 1 f, c out = 1 f, for typical values t a = 25 c, for min/max values t a = -40 c to 85 c; unless otherwise noted. (notes 9 and 10) parameter test conditions symbol min typ max unit output voltage (adjustable version) v in = 1.75 v to 6 v i out = 1 ma to 500 ma v out 1.231 (-1.5%) 1.250 1.269 (+1.5%) v output voltage (fixed versions) 1.5 v 1.8 v 2.5 v 2.8 v 3.0 v 3.3 v 5.0 v v in = (v out + 0.5 v) to 6 v i out = 1 ma to 500 ma v out 1.470 1.764 2.450 2.744 2.940 3.234 4.900 (-2%) 1.5 1.8 2.5 2.8 3.0 3.3 5.0 1.530 1.836 2.550 2.856 3.060 3.366 5.100 (+2%) v line regulation v in = (v out + 0.5 v) to 6 v, i out = 1 ma reg line - 4 10 mv load regulation i out = 1 ma to 500 ma reg load - 10 30 mv dropout voltage (adjustable version) (note 9) v do = v in - v out v out = 1.25 v i out = 500 ma v do - 450 470 mv dropout voltage (fixed version) 1.5 v 1.8 v 2.5 v 2.8 v 3.0 v 3.3 v 5.0 v v do = v in - (v out - 0.1 v) i out = 500 ma v out = 0 v to 90% v out(nom) v do - - - - - - - 290 250 200 190 180 170 150 360 300 250 240 230 220 200 mv disable current (NCP606 only) (note 10) v en = 0 v i dis - 0.1 1 a ground current i out = 1 ma to 500 ma i gnd - 145 180 a current limit (note 11) v out = v out(nom) - 10 % i lim 675 - - ma output short circuit current v out = 0 v i sc 700 1000 1350 ma enable input threshold voltage (NCP606 only) voltage increasing, logic high voltage decreasing, logic low high low v th(en) 0.9 - - - - 0.4 v turn-on time (note 11) 1.25 v 1.5 v 1.8 v 2.5 v 2.8 v 3.0 v 3.3 v 5.0 v v in = 0 v to (v out + 0.5 v) or 1.75 v, whichever is higher v out = 0 v to 90% of v out(nom) t on - - - - - - - - 6 6 7 8 10 12 15 30 - - - - - - - - s enable time (NCP606 only) (note 11) 1.25 v 1.5 v 1.8 v 2.5 v 2.8 v 3.0 v 3.3 v 5.0 v v en = from 0 v to v in t en - - - - - - - - 12 12 13 16 18 19 20 30 - - - - - - - - s 7. refer to absolute maximum ratings and application information for safe operating area. 8. performance guaranteed over the indicated operating temperature range by design and/or characterization tested at t j = t a = 25 c. low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 9. maximum dropout voltage is limited to minimum input voltage v in = 1.7 v recommended for guaranteed operation at maximum output current. 10. refer to application information section. 11. values based on design and/or characterization.
ncp605, NCP606 http://onsemi.com 5 electrical characteristics v in = (v out + 0.5 v) or 1.5 v, whichever is higher, c in = 1 f, c out = 1 f, for typical values t a = 25 c, for min/max values t a = -40 c to 85 c; unless otherwise noted. (notes 9 and 10) parameter unit max typ min symbol test conditions power supply ripple rejection (note 11) i out = 500 ma v out = 1.25 v v in - v out = 1 v f = 120 hz, 0.5 v pp f = 1 khz, 0.5 v pp f = 10 khz, 0.5 v pp psrr - - - 62 55 40 - - - db output noise voltage (note 11) f = 10 hz to 100 khz, v out = 1.25 v v n - 50 - v rms thermal shutdown temperature (note 11) t sd - 175 - c thermal shutdown hysteresis (note 11) t sh - 10 - c 7. refer to absolute maximum ratings and application information for safe operating area. 8. performance guaranteed over the indicated operating temperature range by design and/or characterization tested at t j = t a = 25 c. low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 9. maximum dropout voltage is limited to minimum input voltage v in = 1.7 v recommended for guaranteed operation at maximum output current. 10. refer to application information section. 11. values based on design and/or characterization.
ncp605, NCP606 http://onsemi.com 6 typical characteristics figure 9. output voltage vs. temperature (v out = 1.25 v) 1.231 1.2348 1.2386 1.2424 1.2462 1.25 1.2538 1.2576 1.2614 1.2652 1.269 -40 -20 0 20 40 60 80 100 t a , ambient temperature ( c) v out , output voltage (v) v in = v out + 0.5 v = 1.75 v v in = 6.0 v v out = 1.25 v figure 10. output voltage vs. temperature (v out = 2.5 v) 2.45 2.46 2.47 2.48 2.49 2.5 2.51 2.52 2.53 2.54 2.55 -40 -20 0 20 40 60 80 100 t a , ambient temperature ( c) v out , output voltage (v) v in = v out + 0.5 v = 3.0 v v in = 6.0 v v out = 2.5 v figure 11. output voltage vs. temperature (v out = 5.0 v) 4.9 4.92 4.94 4.96 4.98 5 5.02 5.04 5.06 5.08 5.1 -40 -20 0 20 40 60 80 100 v out , output voltage (v) t a , ambient temperature ( c) v in = 6.0 v v in = v out + 0.5 v = 5.5 v figure 12. dropout voltage vs. temperature (v out = 2.5 v) 0 30 60 90 120 150 180 210 240 270 300 -40 -20 0 20 40 60 80 100 v do , dropout voltage (mv) t a , ambient temperature ( c) i out = 500 ma i out = 300 ma i out = 150 ma figure 13. dropout voltage vs. temperature (v out = 5.0 v) 0 20 40 60 80 100 120 140 160 180 200 -40 -20 0 20 40 60 80 100 t a , ambient temperature ( c) v do , dropout voltage (mv) i out = 150 ma i out = 300 ma i out = 500 ma figure 14. ground current vs. temperature 80 90 100 110 120 130 140 150 160 170 180 -40 -20 0 20 40 60 80 1 0 t a , ambient temperature ( c) i gnd , ground current ( a) v out = 5.0 v v out = 2.5 v v out = 1.25 v v in = v out + 0.5 v i out = 500 ma v out = 5.0 v v out = 2.5 v v out = 5.0 v
ncp605, NCP606 http://onsemi.com 7 typical characteristics figure 15. short circuit current limit vs. temperature (v out = 1.25 v) 800 840 880 920 960 1000 1040 1080 1120 1160 1200 -40 -20 0 20 40 60 80 100 t a , ambient temperature ( c) i sc , short circuit current limit (ma) v in = 1.75 v v in = 6.0 v figure 16. psrr vs. frequency (v out = 1.25 v) f, frequency (hz) psrr (db) v out = 1.25 v v in = 2.25 v c out = 1.0 f t a = 25 c i out = 500 ma i out = 1ma figure 17. psrr vs. frequency (v out = 2.5 v) 10 100 1000 10000 100000 psrr (db) f, frequency (hz) v out = 2.5 v v in = 3.5 v c out = 1.0 f t a = 25 c i out = 500 ma i out = 1ma figure 18. noise density vs. frequency (v out = 1.25 v) 0 200 400 600 800 1000 1200 1400 1600 10 100 1000 10000 100000 f, frequency (hz) v n , noise density (nv/ /hz ) v in = v out + 0.5 v = 1.75 v c in = c out = 1.0 f i out = 500 ma t a = 25 c v n = 47 v rms figure 19. noise density vs. frequency (v out = 2.5 v) 0 500 1000 1500 2000 2500 10 100 1000 10000 100000 f, frequency (hz) v n , noise density (nv/ /hz ) v in = v out + 0.5 v = 3.0 v c in = c out = 1.0 f i out = 500 ma t a = 25 c v n = 70 v rms figure 20. load transient (v out = 2.5 v) time (40 s/div) v out 200 mv/div i out 500 ma/div v in = 3.0 v v out = 2.5 v c out = 10 f t rise = t fall = 1 s t a = 25 c v out = 1.25 v 0 10 20 30 40 50 60 70 80 10 100 1000 10000 100000 0 10 20 30 40 50 60 70 80
ncp605, NCP606 http://onsemi.com 8 typical characteristics figure 21. line transient (v out = 2.5 v) time (20 s/div) v in = 2.5 v i out = 500 ma c out = 10 f t rise = t fall = 1 s t a = 25 c v out 100 mv/div v in 500 mv/div 4.0 v 3.0 v figure 22. startup transient (v out = 2.5 v) time (10 s/div) v out 1 v/div v in 1 v/div v out = 2.5 v i out = 0 ma c out = 10 f v in = 3.0 v t rise = 1 s t a = 25 c
ncp605, NCP606 http://onsemi.com 9 definitions general all measurements are performed using short pulse low duty cycle techniques to maintain junction temperature as close as possible to ambient temperature. line regulation the change in output voltage for a change in input voltage. the measurement is made under conditions of low dissipation or by using pulse techniques such that the average junction temperature is not significantly affected. load regulation the change in output voltage for a change in output load current at a constant temperature. dropout voltage the input to output differential at which the regulator output no longer maintains regulation against further reductions in input voltage. measured when the output drops 100 mv below its nominal value. the junction temperature, load current, and minimum input supply requirements af fect the dropout level. ground and disable currents ground current is the current that flows through the ground pin when the regulator operates without a load on its output (i gnd ). this consists of internal ic operation, bias, etc. it is actually the difference between the input current (measured through the ldo input pin) and the output load current. if the regulator has an input pin that reduces its internal bias and shuts off the output (enable/disable function), this term is called the disable current (i dis ). current limit and short circuit current limit current limit is value of output current by which output voltage drops by 10% with respect to its nominal value. short circuit current limit is output current value measured with output of the regulator shorted to ground. psrr power supply rejection ratio is defined as ratio of output voltage and input voltage ripple. it is measured in decibels (db). output noise voltage this is the integrated value of the output noise over a specified frequency range. input voltage and output load current are kept constant during the measurement. results are expressed in v rms or nv / hz . turn-on and turn-off times turn-on time is time difference measured during power-up of the device from the moment when input voltage reaches 90% of its operating value to the moment when output voltage reaches 90% of its nominal value at specific output current or resistive load. turn-off time is time difference measured during power-down of the device from the moment when input voltage drops to 10% of its operating value to the moment when output voltage drops to 10% of its nominal value at specific output current or resistive load. enable and disable times enable time is time difference measured during power-up of the device from the moment when enable voltage reaches 90% of input voltage operating value to the moment when output voltage reaches 90% of its nominal value at specific output current or resistive load. disable time is time difference measured during power-down of the device from the moment when enable voltage drops to 10% of input voltage operating value to the moment when output voltage drops to 10% of its nominal value at specific output current or resistive load. line transient response typical output voltage overshoot and undershoot response when the input voltage is excited with a given slope. load transient response typical output voltage overshoot and undershoot response when the output current is excited with a given slope between no-load and full-load conditions. thermal protection internal th ermal shutdown circuitry is provided to protect the integrated circuit in the event that the maximum junction temperature is exceeded. when activated at typically 175 c, the regulator turns off. this feature is provided to prevent failures from accidental overheating. maximum package power dissipation the power dissipation level at which the junction temperature reaches its maximum operating value.
ncp605, NCP606 http://onsemi.com 10 applications information the ncp605/NCP606 regulator is self protected with internal thermal shutdown and internal current limit. t ypical application circuits are shown in figures 1 to 4. input decoupling (c in ) a ceramic or tantalum 1.0 f capacitor is recommended and should be connected close to the ncp605/NCP606 package. higher capacitance and lower esr will improve the overall line transient response. output decoupling (c out ) the ncp605/NCP606 is a stable component and does not require a minimum equivalent series resistance (esr) for the output capacitor. the minimum output decoupling value is 1.0 f and can be augmented to fulfill stringent load transient requirements. the regulator works with ceramic chip capacitors as well as tantalum devices. larger values improve noise rejection and load regulation transient response. typical characteristics were measured with murata ceramic capacitors. grm219r71e105k (1 f, 25 v, x7r, 0805) and grm21br71a106k (10 f, 10 v, x7r, 0805). no-load regulation considerations the ncp605/NCP606 adjustable regulator will operate properly under conditions where the only load current is through the resistor divider that sets the output voltage. however, in the case where the ncp605/NCP606 is configured to provide a 1.250 v output, there is no resistor divider. if the part is enabled under no-load conditions, leakage current through the pass transistor at junction temperatures above 85 c can approach several microamps, especially as j unction temperature approaches 150 c. if this leakage current is not directed into a load, the output voltage will rise up to a level approximately 20 mv above nominal. the ncp605/ NCP606 contains an overshoot clamp circuit to improve transient response during a load current step release. when output voltage exceeds the nominal by approximately 20 mv, this circuit becomes active and clamps the output from further voltage increase. tying the enable pin to v in (NCP606 only) w ill ensure that the part is active whenever the supply voltage is present, thus guaranteeing that the clamp circuit is active whenever leakage current is present. when the NCP606 adjustable regulator is disabled, the overshoot clamp circuit becomes inactive and the pass transistor leakage will charge any capacitance on v out . if no load is present, the output can charge up to within a few millivolts of v in . in most applications, the load will present some impedance to v out such that the output voltage will be inherently clamped at a safe level. a minimum load of 10 a is recommended. unlike lp8345, for ncp605/606 fixed voltage versions there is no limitation for minimum load current. noise decoupling the ncp605/NCP606 is a low noise regulator and needs no external noise reduction capacitor . unlike other low noise regulators which require an external capacitor and have slow startup times, the ncp605/NCP606 operates without a noise reduction capacitor, has a typical 8 s turn-on time and achieves a 50 v rms overall noise level between 10 hz and 100 khz. enable operation (NCP606 only) the enable pin will turn the regulator on or off. the threshold limits are covered in the electrical characteristics table in this data sheet. the turn-on/turn-off transient voltage being supplied to the enable pin should exceed a slew rate of 10 mv/ s to ensure correct operation. if the enable function is not to be used then the pin should be connected to v in . output voltage adjust the output voltage can be adjusted from 1 times (figure 4) to 4 times (figure 3) the typical 1.250 v regulation voltage via the use of resistors between the output and the adj input. the output voltage and resistors are chosen using equation 1 and equation 2. v out 1.250 1 r 1 r 2 i adj r 1 (eq. 1) r 2 r 1 1 1 v out 1.25 1 (eq. 2) input bias current i adj is typically less than 150 na. choose r 1 arbitrarily to minimize errors due to the bias current and to minimize noise contribution to the output voltage. use equation 2 to find the required value for r 2 . thermal as power in the ncp605/NCP606 increases, it might become necessary to provide some thermal relief. the maximum power dissipation supported by the device is dependent upon board design and layout. mounting pad configuration on the pcb, the board material, and the ambient temperature affect the rate of junction temperature rise for the part. when the ncp605/NCP606 has good thermal conductivity through the pcb, the junction temperature will be relatively low with high power applications. the maximum dissipation the ncp605/NCP606 can handle is given by: p d(max)
t j(max) t a r ja (eq. 3) since t j is not recommended to exceed 125 c (t j(max) ), then the ncp605/NCP606 soldered on 645 mm 2 , 1 oz copper area, fr4 can dissipate up to 1.3 w when the ambient
ncp605, NCP606 http://onsemi.com 11 temperature (t a ) is 25 c. see figure 23 for r ja versus pcb area. the power dissipated by the ncp605/NCP606 can be calculated from the following equations: p d v in i gnd @i out i out v in v out (eq. 4) or v in(max) p d(max) v out i out i out i gnd (eq. 5) 0 50 100 150 200 250 0 200 400 600 800 figure 23. thermal resistance vs. copper area copper area (mm 2 ) r ja , ( c/w) fr4 = 1.0 oz fr4 = 2.0 oz hints v in and gnd printed circuit board traces should be as wide as possible. when the impedance of these traces is high, there is a chance to pick up noise or cause the regulator to malfunction. place external components, especially the output capacitor, as close as possible to the ncp605/NCP606, and make traces as short as possible.
ncp605, NCP606 http://onsemi.com 12 ordering information device nominal output voltage (v) marking package shipping ? ncp605mnadjt2g adj p605 adj dfn6 (pb-free) 3000 / tape & reel ncp605mn15t2g 1.5 p605 150 dfn6 (pb-free) 3000 / tape & reel ncp605mn18t2g 1.8 p605 180 dfn6 (pb-free) 3000 / tape & reel ncp605mn25t2g 2.5 p605 250 dfn6 (pb-free) 3000 / tape & reel ncp605mn28t2g 2.8 p605 280 dfn6 (pb-free) 3000 / tape & reel ncp605mn30t2g 3.0 p605 300 dfn6 (pb-free) 3000 / tape & reel ncp605mn33t2g 3.3 p605 330 dfn6 (pb-free) 3000 / tape & reel ncp605mn50t2g 5.0 p605 500 dfn6 (pb-free) 3000 / tape & reel NCP606mnadjt2g adj p606 adj dfn6 (pb-free) 3000 / tape & reel NCP606mn15t2g 1.5 p606 150 dfn6 (pb-free) 3000 / tape & reel NCP606mn18t2g 1.8 p606 180 dfn6 (pb-free) 3000 / tape & reel NCP606mn25t2g 2.5 p606 250 dfn6 (pb-free) 3000 / tape & reel NCP606mn28t2g 2.8 p606 280 dfn6 (pb-free) 3000 / tape & reel NCP606mn30t2g 3.0 p606 300 dfn6 (pb-free) 3000 / tape & reel NCP606mn33t2g 3.3 p606 330 dfn6 (pb-free) 3000 / tape & reel NCP606mn50t2g 5.0 p606 500 dfn6 (pb-free) 3000 / tape & reel ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d.
ncp605, NCP606 http://onsemi.com 13 package dimensions dfn6 3x3.3 mm, 0.95 pitch case 506ax-01 issue o date 20 jan 2006 *for additional information on our pb-free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* ??? ??? ??? ??? c 0.15 2x 2x top view d e c 0.15 notes: 1. dimensions and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. dimension b applies to plated terminal and is measured between 0.25 and 0.30 mm from terminal. 4. coplanarity applies to the exposed pad as well as the terminals. e2 bottom view b 0.10 6x l 13 0.05 c ab c d2 4x e l1 64 6x 6x (a3) c c 0.08 6x c 0.10 side view a1 a seating plane dim min nom max millimeters a 0.80 --- 0.90 a1 0.00 --- 0.05 a3 0.20 ref b 0.30 --- 0.40 d 3.00 bsc d2 1.90 --- 2.10 e 3.30 bsc e2 1.10 --- 1.30 e 0.95 bsc k 0.20 --- --- l 0.40 --- 0.60 (note 3) k l1 0.00 --- 0.15 6x 0.83 2.15 1.35 1 0.50 0.95 pitch 3.60 dimensions: millimeters 6x on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. typical parameters which may be provided in scillc data sheets and/or specifications can and do vary in different applications and actu al performance may vary over time. all operat\ ing parameters, including typicals must be validated for each customer application by customer's technical experts. scillc d oes not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its of ficers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associ\ ated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufact ure of the part. scillc is an equal opportunity/ affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800-282-9855 toll free ?usa/canada europe, middle east and africa technical support: ?phone: 421 33 790 2910 japan customer focus center ?phone: 81-3-5773-3850 ncp605/d literature fulfillment : ?literature distribution center for on semiconductor ?p.o. box 5163, denver, colorado 80217 usa ? phone : 303-675-2175 or 800-344-3860 toll free usa/canada ? fax : 303-675-2176 or 800-344-3867 toll free usa/canada ? email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your loca l sales representative

▲Up To Search▲

Price & Availability of NCP606

	To Download NCP606 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .